2.5 level kit and 35's....no problem!
#61
i ran 33x12.5X17X9 baha claws with no leveling kit or any lift other than the factory block. i only had to put a couple washers in the front bumper to push it forward, after that on or off road no rubbing that i noticed. ive been in mud holes up and down hills and never tore up a tire or a fender. if the tire ever did hit the inside of the fender well it was'nt anything to cry about.
I also had 35's on my black truck with a 2.5" leveling kit, but my aftermarket wheels were offset perfect to not have any rubbage. We are talking about a 10" wide wheel with a 4.5" offset.
#62
#63
i have top gun customz 2.5 inch leveling kit on a 04 reg cab xlt 4x4 with 17x9 moto metal 951's. i run 285/70 17s rite now but when these tires are done i want to run 35 inch mud grapplers. do you guys think they'll fit without any cutting? they stick out pretty good. heres a pic of what i have now:
#65
i have top gun customz 2.5 inch leveling kit on a 04 reg cab xlt 4x4 with 17x9 moto metal 951's. i run 285/70 17s rite now but when these tires are done i want to run 35 inch mud grapplers. do you guys think they'll fit without any cutting? they stick out pretty good. heres a pic of what i have now:
#67
Yes....I'm proof you can....Dillion thinks you can't run 37's on a T bar crank and a 3" body lift on a 97-03 F150 but me and my friends do that to.
But let me add you will have to do some trimming. NOT hacking just trimming. This is not the end of the world. It's easy to do.
But let me add you will have to do some trimming. NOT hacking just trimming. This is not the end of the world. It's easy to do.
Last edited by westtnfx4; 02-20-2011 at 01:27 PM.
#68
Why do people whine so much about having to trim? We drive FORD F-150's not Ferarri F150's ha. I crammed 35x12.5x18 TOYO MT's on 18x9.5 wheels with 0MM offset and I ha to cup a little off the front and back, but not a single rub otherwise. This is my old truck. To be honest, it should go like this, 2"=33-34, 2.5"=35, 4"=35-36, 6"= 37's, 8"= 38's and so on.
I had plenty of room, on a 2wd none-the-less.
I had plenty of room, on a 2wd none-the-less.
#69
#70
Why do people whine so much about having to trim? We drive FORD F-150's not Ferarri F150's ha. I crammed 35x12.5x18 TOYO MT's on 18x9.5 wheels with 0MM offset and I ha to cup a little off the front and back, but not a single rub otherwise. This is my old truck. To be honest, it should go like this, 2"=33-34, 2.5"=35, 4"=35-36, 6"= 37's, 8"= 38's and so on.
I had plenty of room, on a 2wd none-the-less.
I had plenty of room, on a 2wd none-the-less.
That's a good looking truck yes that's a good chart to go buy^^
Listen guys this is not voodoo magic and I didnt sell my soul to the devil to do this. Its rather simple.
#71
Sorry but since when does cutting plastic make something rust? If you wash all that crud out from under your truck, it wont rust... and a couple inches of plastic isnt going to stop something from rusting. Just my opinion. I was stationed in Maryland during the winter last year and the truck above had zero rust after I moved back to Texas.
#72
Just to make all the non-believers mad, heres a 2WD with 6" on 37's.... Best looking F150 ever built IMO.
#73
i wouldnt mind trimming, i was just wondering if it was required. lol i'll deff go 35's because the 285/70's look a bit to small and to me a little trimming won't hurt anything at all, plus the look of a more full wheel well looks better i think.
brazzeal15, that truck is awesome looking! lol im jealous to say the least..
brazzeal15, that truck is awesome looking! lol im jealous to say the least..
#74
#75
i have top gun customz 2.5 inch leveling kit on a 04 reg cab xlt 4x4 with 17x9 moto metal 951's. i run 285/70 17s rite now but when these tires are done i want to run 35 inch mud grapplers. do you guys think they'll fit without any cutting? they stick out pretty good. heres a pic of what i have now: