F150online Forums
IMG 3617
IMG 3617
0 2010/03/22 16:30:52
IMG 3616
IMG 3616
0 2010/03/22 16:30:00
IMG 3615
IMG 3615
0 2010/03/22 16:30:00
IMG 3614
IMG 3614
0 2010/03/22 16:30:00
IMG 3612
IMG 3612
0 2010/03/22 16:28:33
IMG 3610
IMG 3610
0 2010/03/22 16:28:33
IMG 3609
IMG 3609
0 2010/03/22 16:28:33
Diamo Karat from Indo...
Diamo Karat from Indo...
0 2010/02/23 18:41:18
Diamo Karat from Indo...WIDE!
Diamo Karat from Indo...WIDE!
0 2010/02/23 18:41:18
Nov 2009 Signature
Nov 2009 Signature
0 2009/11/09 15:10:14
uca angle (contrast enhanced)
uca angle (contrast enhanced)
0 2009/09/01 11:23:52
cv angle
cv angle
0 2009/09/01 11:23:52
FourWinns029
FourWinns029
0 2009/08/14 18:36:34
FourWinns024
FourWinns024
0 2009/08/14 18:36:34
Cutting is required...
Cutting is required...
0 2009/06/25 10:11:39
Close up of ball joint angle
Close up of ball joint angle
0 2009/06/23 15:46:15
0 2009/06/17 20:56:40
BakFlip G2
BakFlip G2
0 2009/06/17 20:56:40
Front crossmember support bracket...bolts on using existing holes
Front crossmember support bracket...bolts on using existing holes
0 2009/06/17 20:54:40
Front crossmember support bracket...bolts on using existing holes
Front crossmember support bracket...bolts on using existing holes
0 2009/06/17 20:54:40
0 2009/06/17 20:54:40
FX4 Decal
FX4 Decal
0 2009/06/17 20:54:40
CV spacer all buttoned up. Thread locker was used on every connector, especially these bolts.
CV spacer all buttoned up. Thread locker was used on every connector, especially these bolts.
0 2009/06/17 15:12:55
My cuz'n Charlie putting the final touches on his side...
My cuz'n Charlie putting the final touches on his side...
0 2009/06/17 15:12:55
One side is completely done!
One side is completely done!
0 2009/06/17 15:12:55
Front cross member finally installed.
Front cross member finally installed.
0 2009/06/17 15:04:28
Moog upper control arm is installed. I decided to replace my balljoints during the lift installation. The entire upper arm was replaced but the BJ can be replaced by itself in the future.
Moog upper control arm is installed. I decided to replace my balljoints during the lift installation. The entire upper arm was replaced but the BJ can be replaced by itself in the future.
0 2009/06/17 15:04:28
Tread depth on these ProComp Xtreme ATs are DEEP!
Tread depth on these ProComp Xtreme ATs are DEEP!
0 2009/06/17 15:04:28
Width and height comparo: 35x12.50r18 ProComp XTreme AT vs 325/60r18 Nitto TG's. The Nitto's are mounted and aired up -the XTreme ATs are not mounted.
Width and height comparo: 35x12.50r18 ProComp XTreme AT vs 325/60r18 Nitto TG's. The Nitto's are mounted and aired up -the XTreme ATs are not mounted.
0 2009/06/17 15:04:28
Tearing it all apart...
Tearing it all apart...
0 2009/06/17 15:02:01
I did one side, my cuz'n did the other.
I did one side, my cuz'n did the other.
0 2009/06/17 15:02:01
Tearing it all apart...
Tearing it all apart...
0 2009/06/17 15:02:01
0 2009/06/17 10:36:34
0 2009/06/17 10:36:34
0 2009/06/17 10:36:34
0 2009/06/17 10:36:34
0 2009/06/17 10:35:30
0 2009/06/17 10:35:30
IMG 2452
IMG 2452
0 2009/06/17 10:34:09
IMG 2451
IMG 2451
0 2009/06/17 10:34:09