F150online Forums
Pulley and shaft
Pulley and shaft
0 2014/08/10 10:38:59
image
image
0 2014/06/05 20:14:57
Deleted standard hose clamps and used t-bolt clamps
Deleted standard hose clamps and used t-bolt clamps
0 2014/06/05 12:16:44
Steeda Belt Tensioner
Steeda Belt Tensioner
0 2014/06/01 15:25:45
image
image
0 2014/06/01 15:25:45
image
image
0 2014/06/01 15:25:45
Complete and cleaned up.
Complete and cleaned up.
0 2014/06/01 15:21:25
Overview with 90MM throttle body
Overview with 90MM throttle body
0 2014/06/01 15:08:57
Insulated the CAI to prevent heat soak
Insulated the CAI to prevent heat soak
0 2014/06/01 15:08:57
Now with 4" intake and Ford Motorsports 90MM throttle body
Now with 4" intake and Ford Motorsports 90MM throttle body
0 2014/06/01 15:08:57
image
image
0 2014/05/26 18:30:11
image
image
0 2014/05/26 18:30:11
Close up
Close up
0 2014/05/25 16:56:31
GT500 Heat Exchanger install complete. The Whipple part is on top and The other down at the bottom.
GT500 Heat Exchanger install complete. The Whipple part is on top and The other down at the bottom.
0 2014/05/25 16:40:46
Centric rotors and EBC Yellow Stuff pads on the rear.
Centric rotors and EBC Yellow Stuff pads on the rear.
0 2014/05/25 14:32:34
Crusing at 73mph. Ambient temp 71. IAT's 86. A 13 degree improvement.
Crusing at 73mph. Ambient temp 71. IAT's 86. A 13 degree improvement.
0 2014/05/24 18:18:17
125mph 12psi and IAT's peaked at 110 degrees. A 16 degree improvement.
125mph 12psi and IAT's peaked at 110 degrees. A 16 degree improvement.
0 2014/05/24 18:12:35
123 mph. 12psi and IAT's reached 108 degrees
123 mph. 12psi and IAT's reached 108 degrees
0 2014/05/24 18:12:35
Installed. Have to make upper supports but ot's and functional.
Installed. Have to make upper supports but ot's and functional.
0 2014/05/24 18:08:20
Rear view
Rear view
0 2014/05/24 08:43:02
Part Number
Part Number
0 2014/05/24 08:43:02
Stock GT500 HE 07-12
Stock GT500 HE 07-12
0 2014/05/24 08:43:02
The stock Whipple/Fluidyne heat exchanger and the GT500 Heat exchanger laid out and ready to install.
The stock Whipple/Fluidyne heat exchanger and the GT500 Heat exchanger laid out and ready to install.
0 2014/05/24 08:17:55
image
image
0 2014/05/06 21:44:49
Connected stock Sirius antenna to Sirius SVX 200 and then to Pioneer AVH8500. Simply removed plastic plug end.
Connected stock Sirius antenna to Sirius SVX 200 and then to Pioneer AVH8500. Simply removed plastic plug end.
0 2014/01/12 20:10:53
90mm Ford throttle body adapted to Roush intake.
90mm Ford throttle body adapted to Roush intake.
0 2014/01/12 17:05:29
90mm verses stock
90mm verses stock
0 2014/01/12 17:04:40
Microphone fot perfectly where old MP3 jack was.
Microphone fot perfectly where old MP3 jack was.
0 2014/01/12 15:18:33
Pioneer AVH 8500 with my AutoMeter gauges
Pioneer AVH 8500 with my AutoMeter gauges
0 2014/01/12 15:16:13
Roush inlet
Roush inlet
0 2014/01/04 14:19:43
image
image
0 2013/12/25 09:09:25
image 2964685753
image 2964685753
0 2013/12/21 05:13:29
image 3506389950
image 3506389950
0 2013/12/21 05:13:18
Underhood shot of the Shelby Vent
Underhood shot of the Shelby Vent
0 2013/12/14 13:20:21
Cut made
Cut made
0 2013/12/08 16:21:49
Prep for cut out
Prep for cut out
0 2013/12/08 16:20:31
Shelby Vent
Shelby Vent
0 2013/12/08 16:20:31
image
image
0 2013/11/23 13:04:44
Cracked stock flexplate
Cracked stock flexplate
0 2013/11/23 13:04:44
SFI Stamp
SFI Stamp
0 2013/11/20 15:16:40