Sea Foam Help
Thread Starter
|
Senior Member
Joined: Jun 2006
Posts: 2,970
Likes: 0
From: Huntsville/Cypress, TX
Originally Posted by jbrew
Just tell your DAD that the cats are constipated - what kinduh look do you think you'll get - haha
Technical Article Contributor
Joined: Oct 2005
Posts: 25,641
Likes: 19
From: MI
That would be funny to see - just say - Dad , just trust me on this one , uhmm, wheres the SawZall 
I had flowmaster 50 series for awhile , that wasn't like 40's - after swapping for the Magnaflow , it was quieter until yuh got on it and it was great .. I removed the rear cats and it was awesome!!
But don't remove or gut the fronts - I just did that - what a mistake - I 'm in the process of correcting the situation - it's up 3 feet in the air out in the shop right now lol..
I had flowmaster 50 series for awhile , that wasn't like 40's - after swapping for the Magnaflow , it was quieter until yuh got on it and it was great .. I removed the rear cats and it was awesome!!
But don't remove or gut the fronts - I just did that - what a mistake - I 'm in the process of correcting the situation - it's up 3 feet in the air out in the shop right now lol..
Last edited by jbrew; Jun 24, 2007 at 03:38 AM.
Technical Article Contributor
Joined: Oct 2005
Posts: 25,641
Likes: 19
From: MI
HAHA - I'll take a picture tomorrow of what I just did to my truck with the Tiger saw
You can show him the pic and tell him this is what you have in mind ... I 'll post one tomorrow..
Shoot , I went thru about 6 blades yesterday..
You can show him the pic and tell him this is what you have in mind ... I 'll post one tomorrow..
Shoot , I went thru about 6 blades yesterday..
Last edited by jbrew; Jun 24, 2007 at 04:01 AM.
Senior Member
Joined: Dec 2006
Posts: 104
Likes: 0
From: Spokane, Wa.
??
Originally Posted by jbrew
Your Right , you have the coil pacs, my mistake - But yeah , that's below average mileage .. Do they test emissions or what not where you are ? - I guess most states do some kind of vehicle check nowadays .
The safe way to go on the exhaust is to get rid of the old cat setup - the whole thing and get one MAGNAFLOW HF cat per side - very O2 friendly and will pass Emissions - but best of all , she'll breath and perform as well . Definitely get better mileage than the 4 cat design ..
What do you want it to sound like ? quiet ? loud? I like the GT sound at take off - so do the woman
Get rid of the rear cats and replace with a strait pipe - leave the front ones alone and put a half way decent muffler in the back and you'll have good sound and more pickup..
The safe way to go on the exhaust is to get rid of the old cat setup - the whole thing and get one MAGNAFLOW HF cat per side - very O2 friendly and will pass Emissions - but best of all , she'll breath and perform as well . Definitely get better mileage than the 4 cat design ..
What do you want it to sound like ? quiet ? loud? I like the GT sound at take off - so do the woman
Get rid of the rear cats and replace with a strait pipe - leave the front ones alone and put a half way decent muffler in the back and you'll have good sound and more pickup..
Technical Article Contributor
Joined: Oct 2005
Posts: 25,641
Likes: 19
From: MI
Originally Posted by rogue1
So whaddayado with the rear 02 sensors if you yard out the rear cats?
The O2 sensors arent't installed in the cats ..
O2 's read and switch fine ..
I'll take some pics when I go out there in a little bit.
Last edited by jbrew; Jun 24, 2007 at 01:23 PM.
Global Moderator &
Senior Member
Senior Member
Joined: Aug 2005
Posts: 21,337
Likes: 159
From: DFW
IMO gut the fronts, and leave the backs. You are guaranteed not to throw a code.
I ran my sea foam through the IAC. Paul showed me how to do it. He said it cleans out the IAC that way too.
I ran my sea foam through the IAC. Paul showed me how to do it. He said it cleans out the IAC that way too.
Senior Member
Joined: Dec 2006
Posts: 104
Likes: 0
From: Spokane, Wa.
What if?
So, if I scrap the whole 9 yards and put in the high flow maggies, I just screw the stock front 02 sensors in the maggies, and leave the rears in the pipe? Will that mod. dork my custom TP ex-cal tunes in any way?
Senior Member
Joined: Mar 2007
Posts: 560
Likes: 0
Originally Posted by rogue1
So, if I scrap the whole 9 yards and put in the high flow maggies, I just screw the stock front 02 sensors in the maggies, and leave the rears in the pipe? Will that mod. dork my custom TP ex-cal tunes in any way?
Thread Starter
|
Senior Member
Joined: Jun 2006
Posts: 2,970
Likes: 0
From: Huntsville/Cypress, TX
Originally Posted by jbrew
HAHA - I'll take a picture tomorrow of what I just did to my truck with the Tiger saw
You can show him the pic and tell him this is what you have in mind ... I 'll post one tomorrow..
Shoot , I went thru about 6 blades yesterday..
You can show him the pic and tell him this is what you have in mind ... I 'll post one tomorrow..
Shoot , I went thru about 6 blades yesterday..
Thread Starter
|
Senior Member
Joined: Jun 2006
Posts: 2,970
Likes: 0
From: Huntsville/Cypress, TX
lol. ive got some rust in mine too. i heard it was not very easy to get off. i watched a friend take his off,. and he had to have like 5 ppl help him lift it off, it looked like a PITA
