F150online Forums
Newly-resized endcap box that helps connect the console to the dash.
Newly-resized endcap box that helps connect the console to the dash.
0 2012/01/28 06:24:18
Top finish piece replaced, once the inner shell was installed.
Top finish piece replaced, once the inner shell was installed.
0 2012/01/28 06:24:18
Front shot of inner shell/shifter assembly. I did not purchase the front metal bracket for the console to mount to the floorboard, but everything fit together nicely.
Front shot of inner shell/shifter assembly. I did not purchase the front metal bracket for the console to mount to the floorboard, but everything fit together nicely.
0 2012/01/28 06:24:18
Shifter sitting in its rightful place, instead of on the floor. This is after I've connected the inner plastic shell and am screwing down and mounting the shifter.
Shifter sitting in its rightful place, instead of on the floor. This is after I've connected the inner plastic shell and am screwing down and mounting the shifter.
0 2012/01/28 06:24:18
Front shot of the shell, with ductwork.
Front shot of the shell, with ductwork.
0 2012/01/28 06:31:44
The inner shell I'm taling about. If you buy a console and decide to do this project, make sure it has this inside. It contains the ductwork needed to make the rear vents operational, the mounting plate for the floor shifter, and the console should come with a wiring harness. The harness should have a connector that mates to a connector in the dash, another head that connects to the floor shifter, and a third harness that will connect to your rear 12v power point.
The inner shell I'm taling about. If you buy a console and decide to do this project, make sure it has this inside. It contains the ductwork needed to make the rear vents operational, the mounting plate for the floor shifter, and the console should come with a wiring harness. The harness should have a connector that mates to a connector in the dash, another head that connects to the floor shifter, and a third harness that will connect to your rear 12v power point.
0 2012/01/28 06:31:44
Inside cab shot
Inside cab shot
0 2012/01/28 06:31:44
Endcap box (original look/design credit goes to pa_wolf) before install. I had to trim 1 inch off the rear of the box to make it sit flush, once the inner shell was installed. The arms on the end of it protruded just a little bit too far.
Endcap box (original look/design credit goes to pa_wolf) before install. I had to trim 1 inch off the rear of the box to make it sit flush, once the inner shell was installed. The arms on the end of it protruded just a little bit too far.
0 2012/01/28 06:31:44
Part number for the rear bracket needed to bolt down the Flow Through console. I thought the original bracket that held the jumpseat could be re-used, but it would not let the console bin lower down far enough to sit on the floor properly.
Part number for the rear bracket needed to bolt down the Flow Through console. I thought the original bracket that held the jumpseat could be re-used, but it would not let the console bin lower down far enough to sit on the floor properly.
0 2012/01/28 06:41:49
Pic of the proper bracket...it is shaped like a U.
Pic of the proper bracket...it is shaped like a U.
0 2012/01/28 06:41:49
Boy, these floorboards sure do get dirty:) The wiring you are seeing is for the rear power point.
Boy, these floorboards sure do get dirty:) The wiring you are seeing is for the rear power point.
0 2012/01/28 06:41:49
Bolts used to hold down the jumpseat/new console. These CAN be re-used. The longer bolt is for the rear frame holes, the shorter bolt is used for the front holes. I did not need the front bolts because of not using the front mounting plate for the new console, but make sure you bolt them all the way back into their holes, or you'll be hearing wind and not know where its coming from;)
Bolts used to hold down the jumpseat/new console. These CAN be re-used. The longer bolt is for the rear frame holes, the shorter bolt is used for the front holes. I did not need the front bolts because of not using the front mounting plate for the new console, but make sure you bolt them all the way back into their holes, or you'll be hearing wind and not know where its coming from;)
0 2012/01/28 06:41:49
Console as I received it, out of a tan interior Lariat, as it also had a tan faux-leather lid.
Console as I received it, out of a tan interior Lariat, as it also had a tan faux-leather lid.
0 2012/01/28 06:54:16
My newly repainted console with the lid recovered in black faux-leather. fits in much better with my black and grey interior now.
My newly repainted console with the lid recovered in black faux-leather. fits in much better with my black and grey interior now.
0 2012/01/28 06:54:16
Other side of the console.
Other side of the console.
0 2012/01/28 06:54:16
detail of rear paint job on console
detail of rear paint job on console
0 2012/01/28 08:04:57