Bolts in made plates to go to the body bolts and a plate for the 3/8 bolts on the back side.no pics developed yet have pics after we finished it but is unpainted. Will have pic in cab in next couple days if I can figure out how to do that.Did the same in the 93 and is legal for GT1 so this on should be for the 99.

 

what company, how much?

 

Just finished installing roll bar that took me 8 hrs to form inside Lightning cab no cutting of anything [what a pain , but it looks great]getting ready to install 5 point then ready for Big Bend may move up a class, now to GS [150 mph] have to see if they will let me, still the only pick up so...... Hope to see some of you there particiating.Wish me Luck

 

That's a must see!! Do you have pic's? Also did you bolt or weld togather. Are you just bolted to the floor of the cab or mounted to the frame?

 

Ruslow, can't wait to see them pics.Best of luck in Big Bend!

------------------
"VENOM plays for keeps!"

 

The company is M&M MotorSports, which is me and its the prototype should run around 250.00 plus freight. pic be here weds I hope.

------------------
99 Lightning,93 Lightning,89 Saleen SSC Mustang 66 GT1 Mustang,66 AC Cobra,Plus a few more!!!!!!!

 

Have pics but, they are rather big[1.1mb] so I can post but does any one know how to make them easier to load so that they will load faster?

 

Ruslow
You needed to set the file size when you scanned them. If you would like to send that large file to me I will reduce it and send it back to you so that you can post it. I can also reduce it and post it to zing.com for you too. Your choice and yes I would like to see your roll bar. mikesmotorsport@mediaone.net

------------------
BABolt
SVT#290

 

1.1 MB pic file has to be a BMP

save the file as a JPG

this should get it WAY down in size...

Brad


------------------
* 99.5 Black Lightning (The fastest color I don’t care what Christy Ann Thinks)
* Personal Best ¼ Mile 13.99 @ 97.75 Mph. (Bone stock)
* Ohio Plate SVT2GO
* Waiting on a chip and filter from Sal.. I wanna go faster!
* Factory CD Changer
* Class 3 Towing Hitch
* Factory Tonneau Cover
* 8" Bazooka Tubs
* Kenwood 80 watt *2 amp
* Viper 550 Alarm w/ remort start
* Often found in the bed: 98 Yamaha Banshee/Pro Design Cool head/ Toomey T-5 Chrome Racing Pipes/ Wiseco Power Pistons / Boyesen rad valves

Injection is nice, but I'd rather be blown. 99 Lightning, the best of both worlds!

 

Here are some pics of the roll bar I hope, thanks to BABolt,if I can do this right.Ruslow

------------------
99 Lightning,93 Lightning,89 Saleen SSC Mustang 66 GT1 Mustang,66 AC Cobra,Plus a few more!!!!!!!

 

Ruslow (Stan)
Here is a little help. Nice looking Bar.

Second photo with seat back in position.

Again, Great looking Rollbar in my favorite color.
------------------
BABolt
SVT#290



[This message has been edited by BABolt (edited 04-09-2000).]

 

Don't forget to pad the bar, they can hurt ya without it.

Zonaman

 

Ruslow, I am currently modifying a '00 for Ed and we would like to get as much info as possible on this installation.

Can I get info on M&M Motorsports?

My site is www.rdmcars.com
Ed's site is www.onelapofamerica.com

Check out His truck on both of our sites...

Thanks.

 

nice rollbar..very nice...jw

 

Nice work!!! I know how hard it can be to fabricate a rollbar for a stock vehicle. Now that you have the hard part done I hope you will consider adding a cross brace to triangulate the whole assembly,,,once again nice work..


Barry