quick question
#1
quick question
Ok guys don't beat me up too much for this question but i am thinking of replacing my stock muffler with a MagnaFlow 4" round by 14" long (part # 14416) and all stock piping and maybe a 12" tip but not sure yet
Now I am looking for cheap decent tone not crazy loud just not stock is there gonna be much difference??
I have a 08' 4.6 STX 4x4 FYI
Thanks guys!!
Now I am looking for cheap decent tone not crazy loud just not stock is there gonna be much difference??
I have a 08' 4.6 STX 4x4 FYI
Thanks guys!!
#2
That's a Magnapack so yes you should hear quite a difference. The stock muffler looks like a old-style water heater. lol Do you have all the cats still installed?
I would guess the Magnapack will be quite a bit louder than your stock muffler though. I think the stock muffler is 32" long (somebody correct me if I'm wrong).
I would guess the Magnapack will be quite a bit louder than your stock muffler though. I think the stock muffler is 32" long (somebody correct me if I'm wrong).
#3
#5
thanks for the input and yes its a completely stock system and have no intentions of a true duel setup or any other mods unless its time for a cat replacement but yea deeper is better (gigity) not into the raspy crackling noise not for a DD....the stock muffler has a tinny echoish sound (if that makes sense). I guess the deepest throaty (gigity) sound out of just a muffler replacement is what i am after
so a larger diameter will make it deeper??
so a larger diameter will make it deeper??
Last edited by FFEMTPSTX; 11-29-2011 at 07:40 PM.
#6
Yes.
You need to spend some time on youtube.
I think you would be happy with a round 7x18" Maggy.
Ovals are a bit quiet.
The tip is where you gotta be careful.
Here is a 7x18" on my truck with a 4.6...
http://www.youtube.com/watch?v=u4qxm_5qkvg
It should sound similar on your truck.
The cats are a lot higher flowing then the older trucks.
You need to spend some time on youtube.
I think you would be happy with a round 7x18" Maggy.
Ovals are a bit quiet.
The tip is where you gotta be careful.
Here is a 7x18" on my truck with a 4.6...
http://www.youtube.com/watch?v=u4qxm_5qkvg
It should sound similar on your truck.
The cats are a lot higher flowing then the older trucks.
Last edited by redtherocket; 11-29-2011 at 07:38 PM.
#7
Trending Topics
#8
Yes.
You need to spend some time on youtube.
I think you would be happy with a round 7x18" Maggy.
Ovals are a bit quiet.
The tip is where you gotta be careful.
Here is a 7x18" on my truck with a 4.6...
It should sound similar on your truck.
The cats are a lot higher flowing then the older trucks.
You need to spend some time on youtube.
I think you would be happy with a round 7x18" Maggy.
Ovals are a bit quiet.
The tip is where you gotta be careful.
Here is a 7x18" on my truck with a 4.6...
It should sound similar on your truck.
The cats are a lot higher flowing then the older trucks.
as far as the tips i understand that they act like a bullhorn and amplify the sound more or less adding volume?? Am i close with that info??
#9
^^
Yep.
my apologies, mine was a 3x7x14"
http://images.magnaflow.com/02product/parts/14719.jpg
The 6" round offers an 18" and a 30" in 3" SI/SO
Yep.
my apologies, mine was a 3x7x14"
http://images.magnaflow.com/02product/parts/14719.jpg
The 6" round offers an 18" and a 30" in 3" SI/SO
#10
So you have a 3"?? I was under the assumption that my truck '08 with a 4.6 has 2.5" pipe stock through out. If that's the case I need to look into the 3" cause I don't want to mess with reducers for the obvious reasons.
Thanks again for the input guys
just realized my OP says a 12" tip haha obviously not a 12" diameter probably a 3.5" or 4"X12" tip
Thanks again for the input guys
just realized my OP says a 12" tip haha obviously not a 12" diameter probably a 3.5" or 4"X12" tip
Last edited by FFEMTPSTX; 11-30-2011 at 02:25 PM.