The Anodized black 2.50 and natural aluminum finish 2.62 are both from Carl at 928 motor sports. The 2.50 had too much anodizing on the inside and as a result I damaged it trying to get it on and then of again. I did not pound on it with a hammer rather I put it in the oven for 10mts at 400gegress and tried to slip it on, when it wouldn’t go easy I pushed it by hand then had to use a pulley puller and to get it off. The inside of the groves are no damaged what so ever. I have sense bought another 2.50 and that’s what I'm using right now. The silver 2.62 saw about 2 months of use and has zero issues. I also have a Vortech brand 3.0 in black with zero issues.

If you want to take the 10mts need with a dreamel you will have a good 2.50 pulley the other 2 need nothing. These are all for a Vortech 20mm shaft not the old school 17mm shafts. Pay pal only and must be sent as a gift to avoid paypals 5% fee Thanks

Damaged 2.50 $25 shipped OBO
Silver 2.62 $55 shipped OBO
Black Vortech 3.0 $40 shipped OBO "not pictrued in perfect shape"


[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

 

I'm open to offers if i'm over the top on price let it be knowen. By the way the 2,62 and 2.50 are for people that want to make some boost if you like little gains stick with the 3.00 and bigger. thanks John

 

Heres the stock Vortech 3.0 in perfect shape $40 shipped or $35 + $5 for shipping
3 Idlers used for 2 years before upgrading to beter ones. 1 ribed and 2 smoth work and spin just fine no BSing here. $5 each and $5 for shipping
Brand new never used vortech belt paid $60 from vortech for it only to find out i had to get a shorter belt to work with my 2.62 and smaller pulleys. I also have the elbow pipe for the f150 vortech kit $45 shipped or $40 +$5 for shipping this is not pictrued.

[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

 

Some one can take all the above stuff less the air elbow pipe for $110 plus $10 for shipping. Its on ebay as well. Thanks

 

I've got so many fools asking me on eBay about the pulley sizing to the boost ratio. Dam if they only new that if I put my almost done block in that with 18 psi I would be running in the low 12's with a 4x4 expo dam!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I’ve already had an 89 GT with a KB with 10psi in the high 10'S dam!!!!!!!!!!!!!!

I already now I have to swap to a positive to make low qt times but the mid is so much fun LMFAO and all with a 4x4 Ive killed so many 350 Z’s and stock z28’s LOL

 

Videos to come very soon!!!!!!!!!!!
That’s as soon as I can Figure out to configure them on the DVD to up load on you tube I've already got these crappie videos of my old moded Bd-11 with 12 psi some times and mostly 9psi at 5700 ft in elko, nv but it still keep the ricers in there place loll

I wish I was working to fish this block. No job = no finish on the block. I want to crank her to 18+psi when I can

I reallly thing i need the 4.10's to make the mid to low 13's right now