programming remote start
#1
#2
Join Date: Jun 2002
Location: Under the flightpath of old ORD 22R
Posts: 10,511
Likes: 0
Received 7 Likes
on
7 Posts
About the only thing to program on the Bronze RMST is new RMST fobs.
The Silver RMST start / RKE has this and a note about other options
Forgot I had this URL, just checked and it is still valid as of today
http://www.clubfte.com/users/hawkins/manuals.htm
Adding Remote Controls to Your System:
The system has the ability to operate from up to eight (8) remote controls. Follow
these instructions to add a remote control to your system.
1. Turn vehicle ignition on.
2. Press and hold in the brake pedal.
3. Press and hold programming/override button under the instrument panel.
After 15 seconds, the horn will chirp three (3) times. This indicates that the unit
has entered the remote control programming mode. The brake pedal can be
released at this time.
4. Release the programming/override button.
5. Press the button on the remote control to be programmed.
The horn will sound once, indicating that the system has “learned” that remote
control.
6. Repeat step 5 for any additional remote controls.
7. Turn the vehicle ignition off to exit the programming mode. Test all remote
controls to ensure that they work properly.
The system has the ability to operate from up to eight (8) remote controls. Follow
these instructions to add a remote control to your system.
1. Turn vehicle ignition on.
2. Press and hold in the brake pedal.
3. Press and hold programming/override button under the instrument panel.
After 15 seconds, the horn will chirp three (3) times. This indicates that the unit
has entered the remote control programming mode. The brake pedal can be
released at this time.
4. Release the programming/override button.
5. Press the button on the remote control to be programmed.
The horn will sound once, indicating that the system has “learned” that remote
control.
6. Repeat step 5 for any additional remote controls.
7. Turn the vehicle ignition off to exit the programming mode. Test all remote
controls to ensure that they work properly.
Your Systems Programmable Operating Characteristics:
Your PowerCode system has several programmable settings such as Ignition
triggered door lock, Ignition triggered door unlock and automatic arming features
which can be changed to tailor your systems operation to your own personal desires
and/or requirements. If you are interested in changing any of these settings, call
1-800-FORD-KEY for information regarding the different programmable features and
the steps to change the settings.
Your PowerCode system has several programmable settings such as Ignition
triggered door lock, Ignition triggered door unlock and automatic arming features
which can be changed to tailor your systems operation to your own personal desires
and/or requirements. If you are interested in changing any of these settings, call
1-800-FORD-KEY for information regarding the different programmable features and
the steps to change the settings.
http://www.clubfte.com/users/hawkins/manuals.htm
Last edited by SSCULLY; 04-04-2010 at 10:39 AM.
#3
#5
#6
Join Date: Jun 2002
Location: Under the flightpath of old ORD 22R
Posts: 10,511
Likes: 0
Received 7 Likes
on
7 Posts
When does the horn not chirp then ( only trying programming mode ) ?
The trouble shooting guide in the link above
Is this what happens when you try to remote start ( same t-shoot PDF ) :
The trouble shooting guide in the link above
System will not go into programming?
· Check for 12volts positive and for good ground at the module.
· Check the connection on the A-20 green/violet wire. On certain vehicles
you might have to change the polarity on this wire in programming.
· Check the connection on the A-7 pink wire. Make sure it has 12volts in
key on and run position.
· Check the override/programming button.
· Check the connection on the B-7 brown wire. (2W7Z-19G364-CA only).
· Check for 12volts positive and for good ground at the module.
· Check the connection on the A-20 green/violet wire. On certain vehicles
you might have to change the polarity on this wire in programming.
· Check the connection on the A-7 pink wire. Make sure it has 12volts in
key on and run position.
· Check the override/programming button.
· Check the connection on the B-7 brown wire. (2W7Z-19G364-CA only).
PATS light comes on and vehicle won’t remote start?
· Make sure the Securilok Interface Kit is programmed correctly.
· Check antenna ring mounting around ignition cylinder.
· Make sure that you have the correct PATS bypass kit for your vehicle.
· Make sure that PATS bypass kit is plugged into the correct location.
· Make sure the Securilok Interface Kit is programmed correctly.
· Check antenna ring mounting around ignition cylinder.
· Make sure that you have the correct PATS bypass kit for your vehicle.
· Make sure that PATS bypass kit is plugged into the correct location.
#7
or what should i do exactly?
is it fuse position change?