Femseadoo installed the pedal last night. Here are a couple of pics of the before and after.




------------------
99 4.2 XLT Red Flareside Sport, Homemade open air box with a K&N Filter, Black Nerf bars, catback exhaust,Superchip, Rear 2 inch drop, clear front corners, Helix Throttle Body Spacer. Soon a Belltech 2/4 lowering kit and new wheels.

 

Are those pedals stainless or anodized aluminum? Just curious...
-Joe-


------------------
98 Explorer (Lemon Law Case in Progress)

'00 F-150, X-cab, 4x4, Lariat, Off-road, Trailer Tow, Holandia Sunroof, built 11/99 picked up 10/00!Clear Corners, Manik Stainless Steel 1-piece brush guard, Custom CB wiring, Uniden PC76-XLW CB radio with K-40 Magna-Mount antenna (for now), 1 set of 165 watt KC Daylighters (for now... more on the way) Custom switch mounting plate and overhead console.
List of planned mods: Clear tails, color matched trailer hitch with stainless steel ball, torsion bar tweak, bug deflector, spray in liner, and a tonneau of some sort...

93 Probe GT teal, OE rims painted to match, bone stock drivetrain.

 

I got mine a few days ago. I installed them with out much trouble at all. There anodized aluminum.



------------------
98 F150
Midnight Blue
4X2 Super Cab
4.6L V8
Viper alarm w/ remote start
Tuff Grip spray in
SI/DO Ravin Z-33
BFG 32" ATs.
Uniden Grant LT CB
Dual Whip Firestik II antennas



[This message has been edited by 25_Ag (edited 12-09-2000).]

 

Dbl post.

[This message has been edited by 25_Ag (edited 12-09-2000).]

 

99XLT,
Thanks for the info and the pics. I'll give my pedals another shot when I'm in the mood to get my neck tweaked again. LOL

 

I don't know about you guys, but I've had these pedals on for less than 2 weeks and they're getting scratched all to pieces!

 

Femseadoo so are mine at the end of the brake pedal. The gas pedal is holding up good.

------------------
99 4.2 XLT Red Flareside Sport, Homemade open air box with a K&N Filter, Black Nerf bars, catback exhaust,Superchip, Rear 2 inch drop, clear front corners, Helix Throttle Body Spacer. Soon a Belltech 2/4 lowering kit and new wheels.

 

Yeah, mine got scratched just from putting them on.

------------------
98 F150
Midnight Blue
4X2 Super Cab
4.6L V8
Viper alarm w/ remote start
Tuff Grip spray in
SI/DO Ravin Z-33
BFG 32" ATs.
Uniden Grant LT CB
Dual Whip Firestik II antennas

 

Is the surface of those things rough or smooth? They look good, but if they're rough to the touch it could be painful for us bare-footed California drivers!




------------------
-JonC-
*Silver 2000 4x2 F150 Supercab
*4.6L Triton V8
*BFG 285/75/16 AT KO's
*16 x 8 Panther Custom 108's
*K&N GenII FIPK
*Custom Cat-back w/ Flowmaster 50 Series
*Fabtech 6.5" "Ultimate" suspension lift
*Smittybilt nerf bars
*Extang Black Max soft tonneau
*Stull billet grille
*Clear corners
*tint/vent visors/air deflector
(no, I did NOT get stuck in
the accessory dept. at K-Mart!)

 

The surface is rougher than stock because the area around the hole is raised.
I wanted better grip for my wet booties when driving up the boat ramp.