Police Interceptor motor, Contrary to belief...
There was a not publicized difference for the 97-98 models. I was under the assumtion just like everyone else that they were all the same as any other 4.6. Ford never stated that any change was done, to my knowledge.
I came across a highway interceptor engine amongst the few engines I just purchased. It was noted in the dismantles computed that it was a police Hwy car. I just needed a pre-PI 4.6. To my disbelief upon removing the 2 valve Non-PI heads, the normal 11cc pistons were not in the cylinders. Instead are a set of the common 4 valve almost flat top pistons. I recognized them immediately, since I just built a 4 valve DOHC motor for my F150. I checked everything out on the motor, including gasket dates. The motor was origional, and NOT rebuilt. I have pulled apart newer PI motors from Taxi's which also have an Interceptor badge, and they were normal, with 18cc. dish heads. So I guess that they only made this type of change on the earlier police cars. Lowflyingbird |
I think their are some other undocumented items in the Interceptors cause I saw green top [42#?] injectors on a Crown Vic cop car that was in the city garage. Asked the mechanic had he changed them and he said no that they were original.
If those are 42# what kinda tune does that thing have? |
Someone had to put those on?
You can easily install injectors and tune to make them work. But the HP coverage of a 42lb injector on a naturally aspired 4.6 is just overkill no matter how you look at it. There would be a ton of waste though. I have a 5.4 which ran a Lightning system. I'd think than an injector which could feed a 5.4 under up to 15psi of boost? max? would simply not meter effecienly on a 4.6. My new build is a DOHC 4.6 with a probable HP of 325, feed by 24lb. injectors, doing the math of HP divided buy number of cylinders, I'm well covered.
I just couldn't see 42's on a 4.6. Maybe if some small town cop had the $$$ in the budget to have his patrol car given a 5.4 with a healthy overbore, added a stroker crank, raise the compression up, and some serious cams and gears, MMMM?, maybe? Thinking about that now, that would make for a sweet sleeper car wouldn't it? I dont think I would want to get chased down by a build like that. |
Originally Posted by lowflyingbird
(Post 3202359)
There was a not publicized difference for the 97-98 models. I was under the assumtion just like everyone else that they were all the same as any other 4.6. Ford never stated that any change was done, to my knowledge.
I came across a highway interceptor engine amongst the few engines I just purchased. It was noted in the dismantles computed that it was a police Hwy car. I just needed a pre-PI 4.6. To my disbelief upon removing the 2 valve Non-PI heads, the normal 11cc pistons were not in the cylinders. Instead are a set of the common 4 valve almost flat top pistons. I recognized them immediately, since I just built a 4 valve DOHC motor for my F150. I checked everything out on the motor, including gasket dates. The motor was origional, and NOT rebuilt. I have pulled apart newer PI motors from Taxi's which also have an Interceptor badge, and they were normal, with 18cc. dish heads. So I guess that they only made this type of change on the earlier police cars. Lowflyingbird |
Yes, you are right about that,
I have had many a Ford, and especially in last year models on a platform you find all kinds of changes. Usually good upgrades in brakes, atleast thats what I have found.
My favorite was a 97 extended Aerostar 4.0. It got the automatic 5 speed, while Explorers did not get it until 99. It also had a heavy duty drive shaft with CrownVic size U-joints and rear brakes. I had several Aerostars before that one which had none of that. They were also ext models with the 4.0. The same reason that the early year 97 Explorer 5.0 motors had Cobra GT40 heads. An obvieous left over from the Mustangs that switched to 4.6L. Then mid year and later Explorers all had GT40P heads. I sell them all the time, have three sets now. So, I guess the 42lb injectors are a possibility. It's just that it's a real $$ item and even on injector charts would be a vast overkill. Like mounting a Eaton blower on a Focus, OH?, wait, I think they did that??? |
I checked parts catalog on a 98 and pistons, crank, and cams are all the same. So police package was just a supension upgrade I guess.
Ed |
cool. so do you think its special to the highway car, or just all the earlier 97-98 interceptors?
|
i got a 96p71 alog with my superduty. the block. head and internals are all the same as far i i know. intake and exhaust setup is different.
p71 vs reg crown vic differences. oil,tranny and power steering coolers. heavy duty battery and alternator. idle is set a few hunndred rpms higher to run all the police eqipment. tranny tuned for firmer shifts like a factory shift kit. has the beffier suspension bigger swaybars etc.... |
Originally Posted by keith97xlt
(Post 3203810)
i got a 96p71 alog with my superduty. the block. head and internals are all the same as far i i know. intake and exhaust setup is different.
p71 vs reg crown vic differences. oil,tranny and power steering coolers. heavy duty battery and alternator. idle is set a few hunndred rpms higher to run all the police eqipment. tranny tuned for firmer shifts like a factory shift kit. has the beffier suspension bigger swaybars etc.... |
Neat, I read all the posts, and understood nothing:D
|
Originally Posted by Shinesintx
(Post 3203867)
Neat, I read all the posts, and understood nothing:D
My personal experience is the major difference between the CV and Caprice is the rear door opening. The rear door of the CV is cavernous but, I guaruntee, when you are being placed in the backseat of a Caprice, you are going to bang your head every damn time. Never fails. :mad: |
a 96 caprice 9c1 vs a 96 p71 its no contest...350 kills 4.6. the new p71 is rated at 250 hp at theve crank.ive driven a 01 that was the first year with p.i heads and it moved pretty well.
|
Originally Posted by Raoul
(Post 3203900)
The previous post was pointing out the differences between the Caprice and CV (Crown Victoria) based on personal experience.
My personal experience is.... |
Originally Posted by Patman03SprCrw
(Post 3204102)
How far before the goats was your police experience? :coffee:
|
Originally Posted by Raoul
(Post 3203900)
I guaruntee, when you are being placed in the backseat of a Caprice, you are going to bang your head every damn time.
Never fails. :mad: Another new addition is those kick-plates at the bottoms of the seats. You used to be able to tuck your feet nicely beneath the bottom of the cab divider. Now there is no leg room what-so-ever!! I remember one ride in the back of a cop car; the cop's back-up gun slid from under his seat right to where I was sitting in the back. When he was taking me out of the car, he saw the gun, and accused me carrying it and trying to ditch it in the back seat of his car. He said, "nice gun, I have one just like it". He felt pretty stupid when he figured out that it was his own gun that he was trying to pin on me. |
All times are GMT -4. The time now is 07:29 PM. |
© 2024 MH Sub I, LLC dba Internet Brands