F150online Forums

Tell us your setup! Intake and Exhaust!

Thread Tools
 
Search this Thread
 
  #31  
Old 03-02-2013, 02:33 PM
stoffer's Avatar
Senior Member


Join Date: Apr 2004
Location: missing Texas...
Posts: 13,644
Received 72 Likes on 65 Posts
Originally Posted by Chris's FX4



Originally Posted by 88racing
I thought you were running 44"s....

I switch up to using pringles cans and gorilla duct tape for my intake....keeps the iat temps down better over the paper tubes and regular duct tape....
Originally Posted by dirtrider596979
i didnt realize you were on a canned tune? i thought you had one of those $9.99 Super Power Performance Racing JDM chips i see on ebay all the time.

I hear if you stack up three or four of them you get 300 more horsepower


fixed my post
 
Reply Like
  #32  
Old 03-02-2013, 04:08 PM
Chris's FX4's Avatar
Senior Member
Join Date: Sep 2011
Location: Houghton, MI & Chicagoland
Posts: 285
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by tarajerame
fixed my post
Well, now that puts you right around high idle rpms at about 50-60mph. But hey if physics didn't exist, you would theoretically be getting like 60mpg now.
 
Last edited by Chris's FX4; 03-02-2013 at 04:10 PM.
Reply Like
  #33  
Old 03-03-2013, 08:45 PM
nw150's Avatar
Senior Member
Join Date: Apr 2007
Location: Ohio
Posts: 517
Likes: 0
Received 0 Likes on 0 Posts
390FE with Holley Street Dominator Single Plane Intake, Holley 750cfm w/vac secondaries, 14x3" K&N Filter, Headers, NO cats, 2.5" pipes, Dynomax Bullets, crappy pipe work. Looking forward to getting the exhaust re-run with mandrel bends this year and making better vids.

These are all that I have for now. Engine isn't at operating temp in either:

 
Last edited by nw150; 03-03-2013 at 08:47 PM.
Reply Like
  #34  
Old 03-04-2013, 10:41 AM
1997 lariat 4.6's Avatar
Senior Member
Thread Starter
Join Date: Dec 2011
Location: Lovely Land of Iowa
Posts: 1,854
Likes: 0
Received 3 Likes on 3 Posts
not bad! sounds like its cammed?
 
Reply Like
  #35  
Old 03-04-2013, 06:05 PM
Bullet85_'s Avatar
Suspended
Join Date: Jan 2013
Posts: 30
Likes: 0
Received 0 Likes on 0 Posts
My Bully Dog intake.....Enclosed filter inside and pulls the air from the fender well(kinda like stock but with a cone filter)

Name: IMG_0225_zps5c7786fe.jpg Views: 67 Size: 74.1 KB
Name: IMG_4916_zpscc53fbcb.jpg Views: 76 Size: 76.9 KB
Name: 51200-4.jpg Views: 91 Size: 72.7 KB
 
Reply Like
  #36  
Old 03-05-2013, 02:10 PM
nw150's Avatar
Senior Member
Join Date: Apr 2007
Location: Ohio
Posts: 517
Likes: 0
Received 0 Likes on 0 Posts
As far as I know it's the stock cam with low compression pistons. Like I said it wasn't warmed up in this vid so it was still putt putting along. That and there are two different types of pistons in it, and they are probably different enough to make the idle a little rough. It gets pretty smooth though once at operating temp.

Plans are to have the engine rebuilt with higher compression and a little bigger than an rv cam in it.
 
Reply Like
  #37  
Old 03-09-2013, 08:16 PM
nw150's Avatar
Senior Member
Join Date: Apr 2007
Location: Ohio
Posts: 517
Likes: 0
Received 0 Likes on 0 Posts
New vids, everything is still the same:


 
Reply Like
  #38  
Old 03-11-2013, 12:12 AM
cndrashcroft's Avatar
Member
Join Date: Dec 2011
Location: saskatoon,SK,CANADA
Posts: 65
Likes: 0
Received 0 Likes on 0 Posts
It's all in the sig
 
Reply Like
  #39  
Old 03-11-2013, 01:52 PM
Alweeja's Avatar
Member
Join Date: May 2012
Location: Augusta, Georgia
Posts: 21
Likes: 0
Received 0 Likes on 0 Posts
Stock set up with Maxx-flow mufflers
 
Reply Like
  #40  
Old 03-11-2013, 05:00 PM
2000Bansheeboy's Avatar
Senior Member
Join Date: Apr 2012
Location: Mesa Arizona
Posts: 177
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by dirtrider596979
Im going to be putting one up soon, i had another video request too. i just need to remeber when i have the time, then i gotta figure out how to post the video
Just upload to youtube then post a link to it up here! Nothin too hard!
 
Reply Like
  #41  
Old 03-24-2013, 08:49 PM
BRodst3R's Avatar
Junior Member
Join Date: Oct 2012
Posts: 6
Likes: 0
Received 0 Likes on 0 Posts
I just did rear cat and muffler delete on my truck. Couldn't be happier with it. Will try and get a video up.
 
Reply Like
  #42  
Old 03-26-2013, 02:15 PM
1997 lariat 4.6's Avatar
Senior Member
Thread Starter
Join Date: Dec 2011
Location: Lovely Land of Iowa
Posts: 1,854
Likes: 0
Received 3 Likes on 3 Posts
Finally got a vid to upload...
 
Reply Like
  #43  
Old 03-26-2013, 04:31 PM
dirtrider596979's Avatar
Senior Member
Join Date: Feb 2008
Location: Stony Point NY
Posts: 405
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by 1997 lariat 4.6
Finally got a vid to upload...
http://www.youtube.com/watch?v=z2uFskBveEc
Almost, says its set to private
 
Reply Like
  #44  
Old 03-26-2013, 10:05 PM
1997 lariat 4.6's Avatar
Senior Member
Thread Starter
Join Date: Dec 2011
Location: Lovely Land of Iowa
Posts: 1,854
Likes: 0
Received 3 Likes on 3 Posts
Son of a darnit. should be fixed now...
 
Last edited by 1997 lariat 4.6; 03-26-2013 at 10:10 PM.
Reply Like
  #45  
Old 07-07-2013, 01:42 PM
08FX4SC's Avatar
Senior Member
Join Date: Dec 2012
Location: Wisconsin
Posts: 472
Likes: 0
Received 0 Likes on 0 Posts
2008 F-150 FX4

Intake - Gotts Mod
Air Filter - Stock Motorcraft
Manifolds - Stock
CATS - Stock
Exhaust - Flowmaster American Thunder SIDO / Super 40 (Borla Coming Soon)
 
Reply Like



Advanced Search
Quick Reply: Tell us your setup! Intake and Exhaust!


Reply Closed Thread Share

All times are GMT -4. The time now is 08:58 PM.