F150 4.6 5.4 swap
Hi I'm new to this from and I have a 2002 f150 that I have purchased from a friend. I bought the truck knowing the 4.6 was toast, bent all exhaust valves on passenger side and broken piston. I bought a good running 2001 5.4 and did the swap buy the information I have found on this form but I have run into a bit of a bind. The engine has a hard time starting and once it does start it won't idle at all I have to rev it to keep it running I have tested my tps,maf,O2 sensors ect everything is good except it is running way to rich. I know it's running way to rich because I have a live data scanner.also when I drive it I will go threw has faster then I can put it in. I have used all the 4.6 sensors the only thing I have on the motor that isn't from the 4.6 is the fuel rain, because from the 4.6 to the 5.4 the holes to bolt in the fuel rail don't line up anyone could help I would be thankful and if I left anything out ask 2x4 automatic 150000k on truck I'm stuck
|
Hi Kman - welcome to the forum.
I've moved your thread into the 97-03 truck section because I think you'll get more responses here than in the section reserved for comments about the forum itself. I'm having trouble understanding your post, but it sounds like you are trying to marry parts like sensors from the 4.6 to the 5.4 engine? And, the only accessory you included with the 5.4 was the fuel rail? I've never done an engine swap, but I'd think you need to keep more of the 5.4 accessories with the engine you are adopting. What about the PCM? Did you import it or are you trying to use the one that was married to the 4.6? These are just thoughts, and they may well be off base. I'm sure there are people here who will have much better ideas than mine. - Jack |
Thank u and I'm having an issue with the truck idling and it's running to ritch and I'm am using the 4.6 computer and because I didn't want to switch harnesses I use all the plugs from 4.6 in one of the forms it's says to do this but I'm just having an issue with no idle and running really Rich I also used the 4.6 injectors and the 5.4 fuel rain
|
Im no pro but from what Ive read, the 5.4 computer needs to be used due to fuel trimming
|
Am i able to bolt up 4.6 headers to a 5.4
|
I believe they will, you may have an issue with the angle, this is based on this......
https://www.f150online.com/forums/ar...wap-notes.html FYI if anyone is interested, I have a 99 5.4 PI set up with heads and intake |
Look for an air leak between the MAF and the throttle body. If that proves fruitless look for a leak between the throttle body and the cylinder head. A leak anywhere in these areas will cause your symptoms.
|
Engine swap
Originally Posted by Kman52
(Post 5157140)
Thank u and I'm having an issue with the truck idling and it's running to ritch and I'm am using the 4.6 computer and because I didn't want to switch harnesses I use all the plugs from 4.6 in one of the forms it's says to do this but I'm just having an issue with no idle and running really Rich I also used the 4.6 injectors and the 5.4 fuel rain
Basically, in your case and mines, you will need a tune for your ecm to efficiently run your engine. Make sure to mention which transmission your vehicle has because within the programming are the parameters for transmission also, despite what some say. Most 5.4 use the 4R100 transmission due to the extra power so when people program, they generally default to that unless they have your correct transmission code. I am currently doing another swap from a 97 T bird into a 98 F-150. With that one, I shouldnt have any issues since they are both 4.6 engines. I just wanted to answer this question in case someone ever does the swap and needs an answer. |
Hello. I have a 99 f150 with a 4.6 from a crown vic already installed. The truck came with a 4.6. The crown vic was a 98. Intākes swapped an everything. Wont run. What should i do?
|
What does it do when you try to start it??does not matter if the motor came from crown vic or not, I would think, if its a 4.6 original that 4.6 from the Vic is the same.
|
All of the above was false as far as tuning and all that other stuff. I have done a bazillion of these 4.6L to 5.4L swaps, and they all ran fine. Only known differences are some 4.6Ls use 2 temperature sensors so you can build a T or tap another hole into a water passage. And exhaust is wider on 5.4L. IAC wires will need extended since its further back on the manifold now, temperature sensors wires will need extended as well. EVERYTHING else can stay 4.6L. You DONT want to use certain 5.4L things cause your computer will want to see the sensors from the 4.6L and will be thrown off by slightly different 5.4L sensors. One big one for example, my truck ran poorly with the 5.4L mass air. Dont change them. Mixing 5.4L sensors with 4.6L computer parameters is all bad. Certain things dont matter, certain things do. It's up to you to know what you should and shouldn't use.
|
Good post PAXTON.
This is why I stayed out of. the thread that is a year old. Those who try to become back yard engineers, only twist wrenches and forget the rest, end up with problems, then wonder why it's a problem and still not understand. A 4.6 between a Crown Vic and an F150 is only the same displacement. The application and the program version loaded into the computer has to be different. The vehicle weight is different, transmission converters are different stall speed, the intake runner lengths are greatly different. The fuel and timing maps are different per the engine application. The shift skeds maybe a bit different. After one makes what is considered a successful swap, is only based on satisfaction not the best performance based on the original factory build. |
Some one should have told you to check fuel pressure regulator. I had one rupture and it dumped fuel right up the vacuum. Straight into manifold. It ran just like you described. |
2008 5.4L 3v king ranch
what am I looking at having to do to drop a rebuilt lightning motor ?? |
Mark 8 swap to f150
I'm inquiring on the full extent on swaping a 1996 mark 8 4.6 to a 1998 f150 4.6
what all do I need to pull for it to work was there any modificaticons? |
All times are GMT -4. The time now is 11:19 PM. |
© 2024 MH Sub I, LLC dba Internet Brands