02 Sensor Install

Thread Tools
 
Search this Thread
 
  #1  
Old 11-19-2007, 12:55 PM
02SUPRCRUE's Avatar
Senior Member
Thread Starter
Join Date: Sep 2003
Location: Hellertown, PA
Posts: 136
Likes: 0
Received 0 Likes on 0 Posts
02 Sensor Install

Looking for advice on how to replace the upstreams on my 02 5.4. I have my new Bosch sensors ready to go but I'm a little concerned about getting to the right side. Any and all advice is appreciated. Yes, I alreadt did the search but didn't find what I was looking for.

Thanks!

02 F150 Super Crew Lariat FX4 White & Silver
5.4 /w Roush Cold Air Intake & K&N filter
3.55 LS
Flowmaster Cat Back
JBA Silver Cat4ward Headers
Rancho RSX's
Rancho Steering Stablizer
Hellwig Rear Anti Sway Bar
Lightning Tails
Outland Sport Bumper Guard
Hella 550's
Silverstars
Superchips 9100 Micro Tuner c/o Troyer Performance
Underdrive Pullies c/o Troyer Performance
Mag-Hytec Trans Pan
 
  #2  
Old 11-19-2007, 02:39 PM
stoffer's Avatar
Senior Member


Join Date: Apr 2004
Location: missing Texas...
Posts: 13,644
Received 72 Likes on 65 Posts
it's tight but it was pretty easy on my '01. I just used the open side of the wrench fortuantly i didn't have to heat them
 
  #3  
Old 11-19-2007, 09:37 PM
torkum's Avatar
Senior Member
Join Date: Dec 2005
Location: Lebanon,TN
Posts: 2,426
Likes: 0
Received 2 Likes on 2 Posts
Take the wheel and inner fender off for easy access. Use a good penetrating oil and a 22m wrench. I use Sea Foam brand Deep Creep:

 
  #4  
Old 11-19-2007, 10:22 PM
jbrew's Avatar
Technical Article Contributor

Join Date: Oct 2005
Location: MI
Posts: 25,637
Likes: 0
Received 15 Likes on 15 Posts
Yep!! A 7/8 open end works too..
 
  #5  
Old 11-19-2007, 11:05 PM
scottbigred's Avatar
Senior Member
Join Date: Mar 2007
Posts: 560
Likes: 0
Received 0 Likes on 0 Posts
ya i used a 7/8 open end wrench too. soak them up with some penetrating lube and they should come out. i tried to used that special socket on mine. waste of money. just use an open end wrench and becarefull not to strip them.
 
  #6  
Old 11-20-2007, 08:32 AM
02SUPRCRUE's Avatar
Senior Member
Thread Starter
Join Date: Sep 2003
Location: Hellertown, PA
Posts: 136
Likes: 0
Received 0 Likes on 0 Posts
Thanks for the replies and advice. This will be my after turkey carving project. One last question, do you need to reset the PCM after changing the 02 sensors?

Thanks



02 F150 Super Crew Lariat FX4 White & Silver
5.4 /w Roush Cold Air Intake & K&N filter
3.55 LS
Flowmaster Cat Back
JBA Silver Cat4ward Headers
Rancho RSX's
Rancho Steering Stablizer
Hellwig Rear Anti Sway Bar
Lightning Tails
Outland Sport Bumper Guard
Hella 550's
Silverstars
Superchips 9100 Micro Tuner c/o Troyer Performance
Underdrive Pullies c/o Troyer Performance
Mag-Hytec Trans Pan
 
  #7  
Old 11-20-2007, 09:17 AM
jbrew's Avatar
Technical Article Contributor

Join Date: Oct 2005
Location: MI
Posts: 25,637
Likes: 0
Received 15 Likes on 15 Posts
Can't get around it really - the first thing you do before working on it is disconnect the battery
 
  #8  
Old 11-20-2007, 01:01 PM
02SUPRCRUE's Avatar
Senior Member
Thread Starter
Join Date: Sep 2003
Location: Hellertown, PA
Posts: 136
Likes: 0
Received 0 Likes on 0 Posts
Thanks all Hopefully this goes pretty easy.

02 F150 Super Crew Lariat FX4 White & Silver
5.4 /w Roush Cold Air Intake & K&N filter
3.55 LS
Flowmaster Cat Back
JBA Silver Cat4ward Headers
Rancho RSX's
Rancho Steering Stablizer
Hellwig Rear Anti Sway Bar
Lightning Tails
Outland Sport Bumper Guard
Hella 550's
Silverstars
Superchips 9100 Micro Tuner c/o Troyer Performance
Underdrive Pullies c/o Troyer Performance
Mag-Hytec Trans Pan
 



Quick Reply: 02 Sensor Install



All times are GMT -4. The time now is 01:36 AM.